BassBoss DJ18S

New Sale BassBoss DJ18S

DJ18S Powered Subwoofer

Huge Low End – Smaller, Lighter Cab




The DJ18S is a single 18″ powered subwoofer designed to minimize materials cost and weight and maximize efficiency and output.
The DJ18S is an efficient, universal application, cost-effective single 18″ subwoofer. It features an 18″ driver with a 4″ voice coil and a 2400W amplifier in a U.S.A built Baltic Birch enclosure capable of an incredible output down to 27 Hz !


BASSBOSS cabinets are hand-built in the USA.

Constructed from 18mm Baltic Birch plywood, using dado joints, screws and advanced composite adhesives. Stainless steel bolts are used to secure the driver, amplifier and pole sockets.


Created to stand up to intense usage.

The cabinet is finished in an extremely rugged, black polyurethane coating. Drivers are protected by a black powdercoated, perforated steel grill, and the amp is recessed into the back of the cabinet for protection from damage.


A 2400W RMS amplifier with integrated, comprehensive DSP is included.

The amplifier is rated for RMS output using continuous sine wave signal.


This is not a Peak or Burst power rating.

BASSBOSS uses only continuous RMS power ratings because you’re not going to be using your sub in millisecond bursts. For subwoofer applications, Peak and Burst power ratings are largely irrelevant.


The amplifier is capable of delivering 2400W of continuous output.

This ensures the amp isn’t the limiting factor in the output of low frequencies. Providing abundant power prevents overheating issues and virtually eliminates the damage that clipping a too-small amp can cause.


All that electrical power is converted into acoustical energy by an 18 inch neodymium motor woofer.

This premium-quality driver features a split-wound 100 mm (4 in) copper voice coil, and peak-to-peak excursion capability of up to 57 mm.


The woofer cones are waterproofed.

BASSBOSS woofers can survive light ran, spilled drinks and dusty environments that may leave the drivers needing a thorough cleaning. Keep the amplifiers dry and party on!


High-intensity Neodymium magnets are lighter and provide higher efficiency so the result is a lighter and louder cabinet. 

Split-wound coils produce a more linear force through the range of movement of the cone, which results in lower distortion and improved linearity at high output.


The cones are waterproofed to protect them from possible, accidental exposure to moisture such as rain or spilled beverages. 

Waterproofed woofer cones also permit the cleaning of drivers that have been soiled in a dirty or dusty environment with the use of a damp cloth. Keep the amplifiers dry and party on!



Specifications


ACOUSTICAL

Loudspeaker Description High-output Single 18 inch Subwoofer Frequency Response (±3 dB) 27 – 100 Hz Maximum Sustained Output 127 dB SPL, 1 meter, half-space (ground plane) Max SPL (Peak)* 136 dB Nominal Dispersion (H° x V°) 360 x 360 – Cardioid Mode Available with Multiple Boxes

ELECTRICAL

Amplification 2400 Watt Continuous RMS Class D Subwoofer Amplifier Processing Integrated comprehensive DSP provides high pass, low pass, phase alignment and limiting Electrical Connectors, Amplifier Neutrik powerCON Input (Blue) NAC3FCA Electrical Connector, Mains Standard US 3-pin 120V electrical plug: NEMA 5-15 (Edison) Voltage Operating Range 90-132VAC, 55-65Hz Current Draw, Nominal 360 W, 3A @ 120 volts (typical, 1/8 max power) Signal Input Connector XLR-F Signal Output Connector XLR-M (pass-through only)

PHYSICAL

Enclosure Type Direct radiating, vented enclosure, optimally tuned for high sensitivity at extremely low frequencies Transducer 1 x 18 in. diameter (457 mm) neodymium motor woofer with 4 in. (100 mm) split winding copper voice coil. Waterproof fiber composite cone Cabinet Construction 18 mm Baltic Birch plywood. Equipped with 2 integrated handles, 1 pole socket, and 4 rubber feet Dimensions (HxWxD) 27.5 in. x 20.5 in. x 29.5 in. (28.25 in. high with feet) Net Weight 110 lbs Shipping Weight 120 lbs Exterior Finish Rugged, weatherproof, black textured, bonded high-pressure polyurethane coating Grill Perforated, powder-coated steel Pole Sockets 1 (35 mm) Handles 2 Integrated Handles

OPTIONAL

Transport Dollies Dolly cart, requires 4-part assembly, holds one box for transporting 1 cabinet Covers Heavy-duty padded nylon transport cover for 1 cabinet


Write a review

Note: HTML is not translated!
    Bad           Good

  • $3,125.00
  • $2,495.00
Loading...
Loading...